•  
• Actuators
• All Thread Rod
• AWWA Brass
• Backflow Preventors
• Compression Couplings
• Fittings
• Flange Bolt & Nut Sets
• Hydrants and Valves
• Manholes & Grates
• Meter Boxes
• Penetration Seals
• Pipe
• Pipe Nipples
• Polyethylene Tubing
• Repair Clamps
• Restrainers
• Spool Pieces
• Tapping Machines
• Tapping Sleeves
• Test Plugs
• Valves
• Water Meters
•  

Gate Valves

• Series 03Small Diameter Gate Valves
  The series 03 valve is our small diameter valve (1-inch to 3-inch) with push-on or NPT threaded ends. These valves meet the applicable requirements of AWWA C509.
• Series 18Combi-Tee
  Series 18 is designed to save time on the installation of hydrant laterals. It reduces the number of joints - which reduces leakage. It is competitively priced to replace the cost of the fitting and valve.
• Series 25Grey Iron Gate Valves
  The series 25 valve is our gray and ductile-iron valve that meets or exceeds all of the requirements of AWWA C509. It is available in a wide variety of end configurations, UL approved Post Indicator Valves, Tapping Valves, and OS&Y.
• Series 45Ductile Iron Gate Valves
  The series 45 valve is our all ductile-iron valve that meets or exceeds all of the requirements of AWWA C509. Since they are all ductile iron, they also meet or exceed the requirements of AWWA C515 with the full wall thickness of AWWA C509. It is available in all end configurations including grooved ends, tapping Valves, and OS&Y. The grooved ends are to AWWA C606.
• Series 55Large Diameter Gate Valves
  The series 55 valve is our large diameter ductile-iron gate valve meeting or exceeding the requirements of AWWA C515. It comes in MJ x MJ and FLxFL versions. All valves come pre-fitted with an F16 mounting plate to mount gearing or motorized actuators. Bevel or spur gearing is available on request.
• Series 66Gate Valves with PE Ends
  Series 66 is designed especially for use in polyethylene water distribution systems. The valve is identical to our premier resilient wedge gate valve with one exception: The PE-pipe stubs are already mounted. This means lower installation costs and leak proof joints.

Dezurik Eccentric Plug Valves

Eccentric action and resilient plug facings assure lasting dead-tight shutoff. Clean interior design and straight-through flow allow high maximum flow capacity with minimum pressure drop. Heavy duty stainless steel bearings, choice of resilient plug facings, welded-in corrosion resistant nickel seat and variety of end styles are available. Capable of handling clean and dirty liquids and gases, sludges and slurries. Available from .5" to 72", are rated for tempuratures up to 300 Deg. F., and from 125 psi to 450 psi. Resilient plug facing: drip tight to rating up to 275 psi (1890 kPa)

• Dezurik Eccentric Plug Valve

Dezurik AWWA Butterfly Valves

DeZURIK AWWA butterfly valves meet the requirements of AWWA C504 standards. They are used for shutoff of clean and dirty water and gases. Offset disc design, corrosion resistant shaft, stainless steel disc edge, and self-compensating shaft seals are features on all DeZURIK AWWA valves. Molded-in body seat with disc locators provides positive sealing and longer seat life on sizes 3 - 20" (80 - 500mm). Large valves, 24" and larger (600mm and larger) feature adjustable, replaceable seat, non-hollow disc structure, and rubber seat retained within a dovetail groove in the valve body and locked in place by an epoxy wedge.

• Dezurik Eccentric Plug Valve

Check Valves

This swing check valve was developed for long life and easy maintenance. From the EPDM encapsulated steel door to the design of the hinge assembly, every detail has been designed with the user in mind.

• Check Valves

Brass THD Gate Valves

Ball Valves